Dimplex SP16 Provozní pokyny stáhnout pdf (Strana 6)

Reﬁ t the heater to the wall ﬁ xing bracket (i.e. follow steps as

n Fig. 4 a, b, c and d) and rotate the bottom ﬁ xing bracket

down again and use the screw provided to permanently ﬁ x the

heater in place.

The heater should not be connected until the instruction leaﬂ et

is read fully.

Recessed Installation

Please note that this appliance can also be wall-mounted so

that it is recessed. This can be installed in a large ﬁ replace

opening or a purpose built wall. See Table 1 for size of recess

required and hole ﬁ xing dimensions and Fig. 5a. This ﬁ replace

insert does NOT require venting.

In order to ensure it’s future safety in use, it is essential

that this ﬁ re is securely ﬁ xed to the wall.

IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN

APPROPRIATE TO THE WALL MATERIAL TO WHICH

THE FIRE IS BEING FIXED. SOME MODERN INTERNAL

BUILDING MATERIALS ARE VERY LOW DENSITY BLOCK

AND REQUIRE SPECIALIZED FIXING DEVICES TO

PROVIDE A SAFE,SECURE INSTALLATION.

The installation of this ﬁ re should be carried out by a competent

person. If in doubt please consult your local builder.

This section provides step by step instructions for selecting

a location and preparing the site to install the ﬁ replace into

the following:

Existing Fireplace

1. Make sure that the ﬁ re is located on a ﬂ at surface.

2. Seal all draughts and vents to prevent chimney debris

from falling onto the Fireplace Insert. Do not install into an

existing ﬁ replace that is prone to dampness.

3. Remove the ﬁ re front panel by following the steps as

outlined in ‘Lamp Replacement’ sections.

4. Locate the 4 ﬁ xing holes, position the ﬁ re accordingly, and

ﬁ rmly ﬁ x the appliance to the wall using the appropriate

screws - see Fig. 5a.

5. Replace the front panel.

New Support Structure Construction

When

planning where to position your purpose built support

structure the following steps must be observed:

1. Place the ﬁ re in the desired location to see how it will look

in the room.

2. Mark the desired location for the new support structure

in the room and store the ﬁ re in a safe, dry and dust free

location.

3. Using timber studs to support the ﬁ re, devise and construct

a suitable means of supporting the product within the wall

partition and provide electrical power for the ﬁ re to be HARD

wired. For recommended sizes of height, width and depth

of opening for recess and hole ﬁ xing dimensions for each

model - see Table 1 and Fig. 5a.

4. When the structure is complete, remove the front panel

of the ﬁ re by following the steps as outlined in ‘Lamp

Replacement’ sections.

5. Locate the 4 ﬁ xing holes, position the ﬁ re accordingly, and

ﬁ rmly ﬁ x using the appropriate screws.

6. Replace the front panel.

TABLE 1

X Y Z

1160 1143 520 146

NOTE: The appliance should be HARD wired to an electrical

power outlet when placed in a recessed installation.

Please consult a qualiﬁ ed electrician for appropriate wiring

requirements.

Manual Operation

The switches are located at the bottom right side of the

appliance - see Fig. 6.

Remote Operation

The standby switch (S1) must ﬁ rst be turned ‘ON’.

Note: It

takes some time for the receiver to respond to the

transmitter. DO NOT PRESS the buttons more than once within

two seconds for correct operation.

Manual & Remote Operation

Setting Operation Setting

Flame Effect Press the ‘I’ button X 1 (Switch 3) Top Neon

Flame Effect & 1kw Heat Press the ‘I’ button X 2 (Switch 3) Middle Neon

Flame Effect & 2kw Heat Press the ‘I’ button X 3 (Switch 3) Bottom Neon

The Standby switch must ﬁ rst be turned ‘ON’ to operate the

appliance manually or by remote control.

Note: It takes some time for the receiver to respond to the

transmitter. DO NOT PRESS the buttons more than once within

two seconds for correct operation.

To go to the previous settings press the O button.

Pressing the O button on the remote turns off the appliance. To

turn the appliance back On press the I button - see Fig. 8.

To increase or decrease the brightness of the ﬂ ames, use the

dimmer button or the

button on the Remote Control.

To turn off the power the Standby Switch must be turned

‘OFF’.

1 2 3 4 5 6 7 8 9 10 11 ... 27 28

Komentáře k této Příručce

Žádné komentáře

Dimplex SP16 Provozní pokyny Strana 6

Komentáře k této Příručce

Související produkty a manuály pro Krby Dimplex SP16